View BD4155FV_4836307.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1/16 www.rohm.com 2010.04 - rev.b ? 2010 rohm co., ltd. all rights reserved. power management switch ics for pcs and digital consumer products power switch ic for expresscard tm BD4155FV description BD4155FV is a power management switch ic for the next generation pc card (expresscard tm ) developed by the pcmcia. it conforms to the pcmcia expresscard tm standard, expresscard tm compliance checklist, and expresscard tm implementation guideline. , and obtains the compliance id ?e c100052? from pcmcia. the power switch offers a number of functions - card detector, and system status detector - which are ideally suited for laptop and desktop computers. features 1) incorporates three low on-resistance fets for expresscard tm . 2) incorporates an fet for output discharge. 3) incorporates under voltage lockout (uvlo) protection. 4) employs an ssop-b20 package. 5) built-in thermal shutdown protector (tsd). 6) built-in soft start function. 7) incorporates an over current protection (ocp). 8) built-in enable signal for pll 9) built-in pull up resistance for detecting expresscard tm 10) conforms to the expresscard tm standard. 11) conforms to the expresscard tm compliance checklist. 12) conforms to the expresscard tm implementation guideline. applications laptop and desktop computer s, and other expresscard tm equipped digital devices. product lineup parameter BD4155FV package ssop-b20 ?expresscard tm ? is a registered trademark registered of the pcmcia (per sonal computer memory card international association). no.10029ebt10
BD4155FV technical note 2/16 www.rohm.com 2010.04 - rev.b ? 2010 rohm co., ltd. all rights reserved. absolute maximum ratings parameter symbol limit unit input voltage v3aux_in, v3_in, v15_in -0.3 +5.0 *1 v logic input voltage cppe#,cpusb#,sysr,ec_clkreq#, ec_clken#,ec_rst#,plt_rst# -0.3 v3aux_in+0.3 *1 v logic output voltage perst# -0.3 v3aux_in+0.3 v logic output applied voltage pll_clkreq# -0.3 +5.0 v output voltage v3aux,v3, v15 -0.3 +5.0 * 1 v output current 1 iov3aux 1.0 a output current 2 iov3 2.0 a output current 3 iov15 2.0 a power dissipation 1 pd1 500 *2 mw power dissipation 2 pd2 812.5 *3 mw operating temperature range topr -40 +100 storage temperature range tstg -55 +150 maximum junction temperature tjmax +150 *1 not to exceed pd. *2 reduced by 4.0mw for each increase in ta of 1 over 25 *3 reduced by 6.5mw for each increase in ta of 1 over 25 (when mounted on a board 70m mx70mmx1.6mm glass-epoxy pcb). operating conditions (ta=25 ) parameter symbol min max unit input voltage 1 v3aux_in 3.0 3.6 v input voltage 2 v3_in 3.0 3.6 v input voltage 3 v15_in 1.35 1.65 v logic input voltage cppe#,cpusb#,sysr,ec_clkreq#, ec_clken#,ec_rst#,plt_rst# 0 v3aux_in v logic output voltage 1 perst# 0 v3aux_in v logic output voltage 2 pll_clkreq# 0 3.6 v output current 1 iov3aux 0 275 ma output current 2 iov3 0 1.3 a output current 3 iov15 0 650 ma * this product is not designed to offer protection against radioactive rays.
BD4155FV technical note 3/16 www.rohm.com 2010.04 - rev.b ? 2010 rohm co., ltd. all rights reserved. electrical characteristics (unless otherwise noted, ta=25 v3aux_in =v3_in=3.3v,v15_in=1.5v) parameter symbol standard value unit condition min typ max standby current icc1 - 120 250 a vsysr=0v bias current icc2 - 250 500 a vsysr=3.3v [logic] high level enable input voltage vl hi 2.0 - - v low level enable input voltage vl low - - 0.8 v input current icppe# - 0 1 a cppe#=3.6v 10 - 30 a cppe#=0v icpusb# - 0 1 a cpusb#=3.6v 10 - 30 a cpusb#=0v isysr -1 0 1 a sysr=3.6v iec_clken# 5 0 20 a ec_clken#=3.6v iec_clkreq# -1 0 1 a ec_clkreq#=3.6v iec_rst# -1 0 1 a ec_rst#=3.6v iplt_rst# -1 0 1 a plt_rst#=3.6v [switch v3aux] on resistance r v3aux - 120 220 m ? tj=-10 100 * discharge on resistance r v3aux dis - 60 150 ? [switch v3] on resistance r v3 - 42 100 m ? tj=-10 100 * discharge on resistance r v3 dis - 60 150 ? [switch v15] on resistance r v15 - 60 100 m ? tj=-10 100 * discharge on resistance r v15 dis - 60 150 ? [over current protection] v3 over current ocp v3 1.6 - - a v3aux over current ocpv 3aux 0.35 - - a v15 over current ocp v15 0.8 - - a [low input miss operation prevent block] v3_in threshold voltage vuvlo v3_in 2.70 2.80 2.90 v sweep up v3_in hysteresis voltage Svuvlo v3_in 50 100 150 mv sweep down v3aux_in threshol d voltage vuvlo v3aux_in 2.70 2.80 2.90 v sweep up v3aux_in hysteresis voltage Svuvlo v3aux_in 50 100 150 mv sweep down v15_in threshold voltage vuvlo v15_in 1.15 1.20 1.25 v sweep up v15_in hysteresis voltage Svuvlo v15_in 50 100 150 mv sweep down [power good] v3 power good voltage pg v3 2.700 2.850 3.000 v v3aux power good voltage pg v3aux 2.700 2.850 3.000 v v15 power good voltage pg v15 1.200 1.275 1.350 v perst# low voltage vperst# low - 0.1 0.3 v i perst =0.5ma perst# high voltage vperst# high 3.0 - - v perst delay t perst# 4 10 20 ms pll_clkreq# low voltage v pll - 0.1 0.2 v i pll_clkreq# =0.5ma pll_clkreq# leak current i pll - - 1 a v pll_clkreq# =3.6v [wake up time] v3_in to v3 t v3 0.1 - 3 ms v3aux_in to v3aux t v3aux 0.1 - 3 ms v15_in to v15 t v15 0.1 - 3 ms * design guarantee
BD4155FV technical note 4/16 www.rohm.com 2010.04 - rev.b ? 2010 rohm co., ltd. all rights reserved. reference data fig.5 wakeup wave form (card assert) fig.6 wakeup wave form (usb2.0 assert) fig.7 wakeup wave form (standby active) fig.1 card assert/ de-assert (active) fig.2 card assert/de-assert (standby) fig.4 system active ? standby ( no card ) fig.3 system active ? standby ( card present) fig.8 power down wave form (card de-assert) fig.10 power down wave form (active standby) fig.9 power down wave form (usb2.0 de-assert) fig.11 perst# wave form (card assert/ de-assert) fig.12 pll_clkreq# wave form (card assert/ de-assert) r v3 =3.3 r v3aux =13.2 r v15 =3 cppe#(2v/div) v3(2v/div) v3aux(2v/div) v15(1v/div) cppe#(2v/div) v3(2v/div) v3aux(2v/div) v15(1v/div) sysr(2v/div) v3(2v/div) v3aux(2v/div) v15(1v/div) cppe#(2v/div) v3(2v/div) v15(1v/div) v3aux(2v/div) v3(2v/div) v3aux(2v/div) v15(1v/div) sysr(2v/div) v3(2v/div) v3aux(2v/div) v15(1v/div) cpusb#(2v/div) 500 s/div 500 s/div 500 s/div 5.0ms/div 5.0ms/div 5.0ms/div 500 s/div 500 s/div 500 s/div 5.0ms/div 5.0ms/div 500 s/div cpusb#(2v/div) v3(2v/div) v3aux(2v/div) v15(1v/div) sppe#(2v/div) v3(2v/div) v3aux(2v/div) v15(1v/div) sysr(2v/div) v3(2v/div) v3aux(2v/div) v15(1v/div) v3(2v/div) v3aux(2v/div) v15(1v/div) v3(2v/div) v3aux(2v/div) perst#(2v/div) cppe#(2v/div) v3(2v/div) v3aux(2v/div) pll_clkreq(2v/div) sysr(2v/div) cppe#(2v/div)
BD4155FV technical note 5/16 www.rohm.com 2010.04 - rev.b ? 2010 rohm co., ltd. all rights reserved. fig.17 pll_clkreq# wave form (ec_clkreq# input) fig.18 pll_clkreq# wave form ( ec_clken# input ) fig.19 output voltage (v3_in:off on) fig.20 output voltage (v3aux_in:off on) fig.14 pll_clkreq# wave form (usb2.0 assert/ de-assert) fig.15 perst# wave form (plt_rst input) fig.16 perst# wave form (ec_rst input) fig.22 output voltage (v3_in:on off) fig.21 output voltage (v15_in:off on) fig.13 perst# wave form (usb2.0 assert/ de-assert) v3(2v/div) v15_in(2v/div) v3(2v/div) v3aux(2v/div) v3_in(2v/div) v3(2v/div) v3aux(2v/div) v15(1v/div) v15(1v/div) v3aux_in(2v/di v3aux(2v/div) v15(1v/div) v3(2v/div) r v3 =3.3 r v3aux =13.2 r v15 =3 v3_in(2v/div) v3aux(2v/div) v15(1v/div) r v3 =3.3 r v3aux =13.2 r v15 =3 v3aux_in(2v/div) v3(2v/div) v3aux(2v/div) v15(1v/div) r v3 =3.3 r v3aux =13.2 r v15 =3 v15_in(2v/div) v3(2v/div) v3aux(2v/div) v15(1v/div) fig.23 output voltage (v3aux_in:on off) fig.24 output voltage (v15_in:on off) 5.0ms/div 500 s/div 1.0ms/div 1.0ms/div 500 s/div 500 s/div 500 s/div 500 s/div 500 s/div 5.0ms/div 5.0ms/div 5.0ms/div ec_rst(2v/div) v3(2v/div) perst#(2v/div) usb2.0(2v/div) v3(2v/div) v3aux(2v/div) perst#(2v/div) cpusb#(2v/div) v3(2v/div) v3aux(2v/div) pll_clk#(2v/div) plt_rst#(2v/div) plt_rst#(2v/div) v3(2v/div) ec_clken#(2v/div) v3(2v/div) pll_clkreq#(2v/div) ec_clken#(2v/div) v3(2v/div) pll_clkreq#(2v/div) ec_rst(2v/div) perst#(2v/div) ec_clkreq#(2v/div) ec_clkreq#(2v/div)
BD4155FV technical note 6/16 www.rohm.com 2010.04 - rev.b ? 2010 rohm co., ltd. all rights reserved. reference data output condition list(protect circuit) condition output cpxx# uvlo(v3/v15) uvlo(v3aux) thermal v3/v15 v3aux h - - - l l l on off off hi-z h - on l l off off h h - - on hi-z hi-z output condition list(logic) state input output v3aux_in v3_in v15_in sysr cppe# cpusb# v3/v15 v3aux off 0 0 0 0 x x off off on stand-by 1 x x 1 0 1 1 off off x 0 off on 0 x off on stand-by 1 x x 0 1 1 off off x 0 off off 0 x off off on 1 1 1 1 1 1 off off x 0 on on 0 x on on output condition list(perst#) state input output v3aux_in v3_in v15_in sysr cppe# cpusb# power good plt_rst# ec_rst# perst# off 0 0 0 0 x x x x x l stand-by 1 x x 0 x x x x x l on 1 1 1 1 1 1 x x x l 0 x ng x x l 0 x ok 0 0 l 1 l ok 1 0 l 1 h 1 0 x x x l output condition list(pll_clkreq#) state input output v3aux_in v3_in v15_in sysr cppe# cpusb# power good ec_ clkreq# ec_ clken# pll_ clkreq# off 0 0 0 0 x x x x x hi-z stand-by 1 x x 0 x x x x x l on 1 1 1 1 1 1 x x x h 0 x ng x x h 0 x ok 0 0 l 1 h ok 1 0 h 1 h 1 0 x x x h
BD4155FV technical note 7/16 www.rohm.com 2010.04 - rev.b ? 2010 rohm co., ltd. all rights reserved. block diagram pin configration pin function pin no pin name pin function 1 plt_rst# logic input pin (from host) 2 ec_rst# logic input pin (from host) 3 sysr logic input pin 4 v3_in1 v3 input pin 1 5 v3_in2 v3 input pin 2 6 v3_1 v3 output pin 1 7 v3_2 v3 output pin 2 8 perst# logic output pin 9 ec_clken# logic input pin (from host) 10 gnd gnd pin 11 cpusb# logic input pin 12 cppe# logic input pin 13 v15_1 v15 output pin 1 14 v15_2 v15 output pin 2 15 v15_in1 v15 input pin 1 16 v15_in2 v15 input pin 2 17 v3aux v3aux output pin 18 v3aux_in v3aux input pin 1 19 pll_clkreq# clock enable signal (to pll) 20 ec_clkreq# logic input pin (from card) v3_in,v3aux_in,v15_in v3,v3aux,v15 gnd ec_clken#(from host) ec_clkreq#(from card) pll_clkreq#(to pll) perst#(to card) ec_rst#(from host) plt_rst#(from host) v15-2 v15-1 1.5v/625ma 3.3v aux/275ma v3-2 v3aux v3-1 3.3v/1.30a vd tsd,cl,uvlo tsd,cl,uvlo_aux vd en,sysr cpusb# cppe# vd tsd,cl,uvlo cl uvlo uvlo_aux v3_in v3aux_in v15_in input logic reference block under voltage lock out pump charge protection thermal power good tsd v3aux_in (from host) sysr (from card) cpusb# (from card) cppe# 1.5v 3.3v 3.3v v3_in v3_in2 v3aux_in v15_in1 v15_in2 v3aux_in vd 4 5 18 15 16 12 11 3 10 9 20 19 8 2 1 14 13 17 7 6 v3aux_in ssop-b20 package 1 2 3 4 5 6 7 8 9 10 plt_rst# ec_rst# sysr v3_in1 v3_in2 v3_1 v3_2 perst# ec_clken# gnd cpusb# cppe# v15_1 v15_2 v15_in1 v15_in2 v3aux v3aux_in1 pll_clkreq# ec_clkreq# 20 19 18 17 16 15 14 13 12 11
BD4155FV technical note 8/16 www.rohm.com 2010.04 - rev.b ? 2010 rohm co., ltd. all rights reserved. description of block operation v3_in, v15_in, and v3aux_in these are the input terminals for each channel of a 3ch sw itch. v3_in and v15_in terminals have two pins each, which should be short-circuited on the pc board with a thick co nductor. a large current runs through these three terminals : (v3_in: 1.35a; v3aux_in: 0.275 a; and v15_ in: 0.625 a). in order to lower the output impedance of the connected power supply, it is recommended that ceramic capacitors (with b-type characteristics or better) be provided between these terminals and the ground. specifically, the capacitors should be on the order of 1 f between v3_in and gnd, and between v15_in and gnd; and on the order of 0.1 f between v3aux_in and gnd. v3, v15, and v3aux these are the output terminals for each switch. the v3 and v15 terminals have two pins each, which should be short-circuited on the pc board and connected to an expresscard connector with a thick conductor, as short as possible. in order to stabilize the output, it is recommended that ceramic capacitors (with b-type characteristics or better) be provided between these terminals and the gro und. specifically, the capacitors should be on the order of 10 f between v3 and gnd, and between v15 and gnd; and on the order of 1 f between v3aux and gnd. cppe# this pin is used to find whether or not a pci-express signal comp atible card is present. turns to ?high? level with an input of 2.0 volts or higher, which means that no card is provided, while it turns to ?low? level when the input is lowered to 0.8 vo lts or less, which means that a card is prov ided. controls the on/off, switch sele cting the proper mode based on the status of the system. pull up resistance (100k ? 200k ? ) is built into, so the number of components is reduced. cpusb# this pin is used to find whether or not a usb2.0 signal compatib le card is present. turns to ?high? level with an input of 2.0 volts or higher, which means that no card is provided, while it turns to ?low? level when the input is lowered to 0.8 volts or less, which means that a card is provid ed. controls the on/off switch, select ing the proper mode based on the system status. pull up resistance (100k ? 200k ? ) is built into, so the number of components is reduced. sysr these pins are used to detect the system status. turns to ?hi gh? level with an input of 2.0 volts or higher, which means that the system is activated, while it turns to ?low? level when the input is lowered to 0.8 volts or less, which means that the system is on standby. plt_rst#, ec_rst# these pins are used to control the reset signal (perst#) to a card from the system side. (also referred to as ?sysreset#? by pcmcia.) turns to ?high? level with an input of 2.0 volts or higher, and sets perst# to ?high? and with a ?power good? output. turns to ?low? level and sets perst# to ?low? when the input falls to 0.8 volts or less. perst# this pin is used to send a reset signal to a pci-express comp atible card. reset status is determined by the outputs, plt_rst#, ec_rst#, cppe# system status. turns to ?high? level and activates the pci-expr ess compatible card only if each output is within the ?power good? threshold, with the card inserted and plt_rst#, ec_rst# turned to ?high? level. ec_clken#, ec_clkreq# these pins are used to control the enable signal (pll_clkre q#) to the reference clock. turns to ?high? level and set pll_clkreq# to ?high? when the input rise to 2.0 volts or higher. turns to ?low? level with an input of 0.8 volts or less, and sets pll_clkreq# to ?low? or with a inverting ?power good? output. pll_clkreq# this pin is used to send an enable signal to the reference clock. activation status is determined by the outputs, ec_clken#, ec_clkreq#, cppe# system status. turns to ?low? level and activates the reference clock pll only if each output is within the ?power good? threshold, with the card kept inserted, and ec_clken#, ec_clkreq# turned to ?low?level.
BD4155FV technical note 9/16 www.rohm.com 2010.04 - rev.b ? 2010 rohm co., ltd. all rights reserved. timing chart power on/off status of expresscard tm system status expresscard tm module status power switch status primary auxiliary primary (+3.3v and +1.5v) auxiliary (3.3v aux) off off don?t care off off on on de-asserted off off asserted on on on on de-asserted off off asserted before this off on asserted after this off off expresscard tm states transition diagram system status card status stand-by status :sysr=l card asserted status :cp#=l on status :sysr=h card de-asserted status :cp#=h from on to stand-by status :sysr=h l from de-asserted to asserted status :cp#=hl from stand-by to on status :sysr=l h from asserted to de-a sserted status :cp#=l h v3aux=off v15=v3=off cp#=h ?l ? sysr=l h cp#=l h sysr=h l sysr=h ?l cp#=h sysr=l cp#=l sysr=l cp#=h sysr=h cp#=l sysr=h cp#=l sysr=l h cp#=h l sysr=h cp#=l sysr=h l cp#=l sysr=l cp#=l h v3aux=on v15=v3=on v3aux=on v15=v3=off
BD4155FV technical note 10/16 www.rohm.com 2010.04 - rev.b ? 2010 rohm co., ltd. all rights reserved. BD4155FV evaluation board BD4155FV evaluation board application components part no value company part name part no value company part name r1 0 ? rohm mcr03 series c1 - - - r1a 100k ? rohm mcr03 series c2 - - - r2 0 ? rohm mcr03 series c3 - - - r2a 100k ? rohm mcr03 series c4 1 f murata grm21 series r3 0 ? rohm mcr03 series c6 10 f murata grm21 series r3a 100k ? rohm mcr03 series c9 - - - r9 0 ? rohm mcr03 series c11 - - - r9a 100k ? rohm mcr03 series c12 - - - r11 0 ? rohm mcr03 series c13 10 f murata grm21 series r11a - - - c15 1 f murata grm21 series r12 0 ? rohm mcr03 series c17 1 f murata grm21 series r12a - - - c18 0.1 f murata grm18 series r19 10k ? rohm mcr03 series c20 - - - r20 0 ? rohm mcr03 series r20a 100k ? rohm mcr03 series 2 3 6 7 9 10 c6 gnd v3(s) v3 20 19 18 17 16 15 14 13 12 11 gnd c17 c18 v3aux_in v3aux_in v3aux pll_clkreq# v3aux_in(s) v3aux(s) gnd c15 gnd v15_in v15_in(s) gnd sw2 r2 gnd ec_rst# v3aux_in r2a c2 sw3 v3aux_in gnd r3 gnd sysr r3a c3 1 sw1 r1 gnd plt_rst# v3aux_in r1a c1 gnd 8 perst # gnd sw9 r9 gnd ec_clken# v3aux_in r9a c9 gnd c4 gnd 4 5 v3_in(s) v3_in sw11 r11 gnd cpusb# v3aux_in r11a c11 gnd sw12 r12 gnd cppe# v3aux_in r12a c12 gnd c13 gnd v15 v15(s) sw20 r20 gnd ec_clkreq# v3aux_in r20a c20 gnd v3aux_in r19 ssop-b20 u1 plt_rst# ec_rst# sysr v3_in1 v3_in2 v3_1 v3_2 perst# ec_clken# gnd ec_clkreq# pll_clkreq# v3aux_in1 v3aux v15_in2 v15_in1 v15_2 v15_1 cppe# cpusb# BD4155FV
BD4155FV technical note 11/16 www.rohm.com 2010.04 - rev.b ? 2010 rohm co., ltd. all rights reserved. BD4155FV evaluation board layout silk screen top layer bottom layer mid layer 1 mid layer 2
BD4155FV technical note 12/16 www.rohm.com 2010.04 - rev.b ? 2010 rohm co., ltd. all rights reserved. application circuit (circuit for expresscard tm compliance checklist) heat loss thermal design should allow the device to operate within the follo wing conditions. note that the temperatures listed are the allowed temperature limits. thermal design should allow sufficient margin from these limits. 1. ambient temperature ta c an be no higher than 100c. 2. chip junction temperature tj can be no higher more than 150c. chip junction temperature tj can be determined as follows: chip junction temperature tj is calculated from ic su rface temperature tc under actual application conditions: tj=tc+ j-cw reference value j-c:ssop-b20 35 /w chip junction temperature tj is ca lculated from ambient temperature ta: tj=tc+ j-aw reference value j-a:ssop-b20 250 /w (ic only) 153.8 /w single-layer substrate (substrate surface copper foil area: less than 3%) substrate size 70701.6mm 3 (thermal vias in the board.) most of heat loss in the BD4155FV occurs at the output switch. the power lost is determined by multiplying the on-resistance by the square of output current of each switch. cppe#(12pin) cpusb#(11pin) v3(6,7pin) v3aux(17pin) v15(13,14pin) perst#(8pin) v3_in(4,5pin) v3aux_in(18pin) v15_in(15,16pin) plt_rst#(1pin) ec_rst#(2pin) sysr(3pin) cppe#(1) cpusb#(2) 3.3v(3) 3.3vaux(4) 1.5v(5) perst#(6) 3.3v(7) 3.3vaux(8) 1.5v(9) sysreset#(10) BD4155FV gnd(10pin) or pll_clkreq#(19pin) v3aux_in ec_clken #(9pin) ec_clkreq#(20pin)
BD4155FV technical note 13/16 www.rohm.com 2010.04 - rev.b ? 2010 rohm co., ltd. all rights reserved. equivalent circuit 1pin 2pin< ec_rst#> 3pin 4,5pin 6,7pin 8pin 9pin 11pi n 12pin 13,14pin 15,16pin< v15_in1,v15_in2> 17pin 18pin 19pin 20pin v3 v3_in v3aux_in v3_in v15 v3aux_in v3aux_in v3aux_in v3aux_in v3aux_in v3aux_in v3aux_in v3aux_in v3aux_in v3aux v3aux_in
BD4155FV technical note 14/16 www.rohm.com 2010.04 - rev.b ? 2010 rohm co., ltd. all rights reserved. notes for use 1.absolute maximum ratings although quality is rigorously controlled, the device may be destroyed when applied voltage, operating te mperature, etc. exceeds its absolute maximum rating. because the source (short mode or open mode) cannot be identified once the ic is destroyed, it is important to take physical safety meas ures such as fusing when implementing any special mode that operates in excess of absolute rating limits. 2.thermal design consider allowable loss (pd) under actual operating conditions and provide sufficient margin in the thermal design. 3.terminal-to-terminal short-circuit and mis-mounting when the mounting the ic to a printed circuit board, take utmost care to assure the position and orientation of the ic are corr ect. in the event that the ic is m ounted erroneously, it may be destroyed. the ic ma y also be destroyed when a short-circuit is caused by foreign matter introduced into the clearance between outputs, or between an output and power-gnd. 4.operation in strong el ectromagnetic fields using the ic in strong electromagnetic fields may cause malfunctions. exercise caution in respect to electromagnetic fields. 5.built-in thermal shutdown protection circuit this ic incorporates a thermal shutdo wn protection circuit (tsd circuit). the working temperature is 175c (standard value) with a -15c (standard value) hysteresis width. when the ic chip temperature rises the tsd circuit is activated, while the output terminal is brought to the off state. the built-in tsd circuit is intended exclusively to shut down the ic in a thermal runaway event, and is not intended to protect t he ic or guarantee performance in these conditions. therefore, do not operate the ic after with the expect ation of continued use or subsequent operation once this circuit is activated. 6.capacitor across output and gnd when a large capacitor is connected across the output and gnd, and the v3aux_in is short-circuited with 0v or gnd for any reason, current charged in the capacitor flows into the output and may destroy the ic. therefore, use a capacitor smaller than 1000 f between the output and gnd. 7.set substrate inspection connecting a low-impedance capacitor to a pin when running an inspection with a set substrate may produce stress on the ic. therefore, be certain to discharge electr icity at each process of the operation. to prevent elec trostatic accumulation and discharge in the assembly process, thoroughly ground your self and any equipment that could sustain esd damage, and continue observing esd-prevention procedures in all handling, transfer and storage operation s. before a ttempting to connect the set substrate to the test setup, make certain that the power supply is off. likewise, be sure the power supply is off before removing the subs trate from the test setup. 8.ic terminal input this integrated circuit is a monolithic ic, with p substrate and p + isolation between elements. the p layer and n layer of each element form a, pn junction. when the potential relation is gnd>terminal a>terminal b, the pn junction works as a diode, and when terminal b>gnd termina l a, the pn junction operates as a parasitic transistor. parasitic elements inevitably form, due to the nature of the ic construction. the operation of the parasitic element gives rise to mutual interference between circuits and results in malfunction, and eventually, breakdown. consequently, take utmost care not to use the ic in a way that would cause the parasitic element to ac tively operate, such as applying voltage lower than gnd (p substrate) to the input terminal. 9. gnd wiring pattern if both a small signal gnd and a high current gnd are presen t, it is recommended that the patterns for the high current gnd and the small signal gnd be separated. proper grounding to the reference point of the set should also be provided. in this way, the small signal gnd voltage will by unaffected by the change in voltage stemming from the pattern wiring resistance and the high current. also, pay special attention to avoid undesirable wiring pattern fluctuations in any externally connected gnd component. pin a p+ p+ n n n p p substrate gnd gnd n p n c b e gnd p+ p+ n n resistor npn transistor structure (npn) pin b parasitic diode gnd pin a c e b gnd nearby other device pin b parasitic diode parasitic diode parasitic diode p substrate
BD4155FV technical note 15/16 www.rohm.com 2010.04 - rev.b ? 2010 rohm co., ltd. all rights reserved. 10. electrical characteristics the electrical characteristics in the s pecifications may vary, depending on ambi ent temperature, power supply voltage, circuit(s) externally applied, and/or ot her conditions. therefore, please check all such factors, including transient characteristics, that could affect the electrical characteristics. 11. capacitors applie d to input terminals the capacitors applied to the input terminals (v3_in, v3aux_ in and v15_in) are used to lower the output impedance of the connected power supply. an increase in the output impedance of the power supply may result in destabilization of input voltages (v3_in, v3aux_in and v15_in). it is re commended that a low-esr capacitor be used, with a lower temperature coefficient (change in capacitance vs. change in temperature), recommended capa citors are on the order of 0.1 f for v3aux_in, and1 f for v3_in and v15_in. however, they must be thoroughly checked at the temperature and with the load range expected in act ual use, because capacitor selection depends to a significant degree on the characteristics of the input power supply to be used and the conductor pattern of the pc board. 12. capacitors applied to output terminals capacitors for the output terminals (v3, v3_aux, and v15) , should be connected between ea ch of the output terminals and gnd. a low-esr, low temperature coefficient out put capacitor is recommended-on the order of 1 f for v3 and v15 terminals, and 1 f less for v3_aux. however, they must be thoroughl y checked at the temper ature and with the load range expected in actual use, because capacitor selection depends to a significant degree on the temperature and the load conditions. 13. not of a radiation-resistant design. 14 . allowable loss (pd) with respect to the allowable loss, please refer to the therma l derating characteristics shown in the exhibit, which serves as a rule of thumb. when the system design causes the ic to operate in excess of the allo wable loss, chip temperature will rise, reducing the current capacity and decreasing other basic ic functionality. t herefore, design should always enable ic operation within the allowable loss only. 15. operating range basic circuit functions and operations are warranted within t he specified operating range the working ambient temperature range. although reference values for electrical characteri stics are not warranted, no rapid or extraordinary changes in these characteristics are expected, provided operation is within the normal operating and temperature range. 16. the applied circuit example diagrams presented here ar e recommended configurations. however, actual design depends on ic characteristics, which shou ld be confirmed before operation. also, note that modifying external circuits may impact static, noise and other ic characteristics, includin g transient characteristics. be sure to allow sufficient margin in the design to accommodate these factors. 17. wiring to the input terminals (v3 in, v3aux in, and v15 in) and output terminals (v3, v3aux and v15) of the built-in fet should be carried out with special care. using unnecessar ily long and/or thin conductors may decrease output voltage and degrade other characteristics. 18. heatsink the heatsink is connected to the sub, which should be short-circ uited to the gnd. proper he atsink soldering to the pc board should enable lower thermal resistance. power dissipation ambient temperature (ta) mounted on board 70mm70mm1.6mmglass-epoxy pcb j- a= 153. 8 /w 0 25 75 100 125 150 50 400 200 0 [ ] 800 1000 600 [mw] 100 812.5mw power dissipation (pd) 500mw without heat sink j-a=250.0 /w
BD4155FV technical note 16/16 www.rohm.com 2010.04 - rev.b ? 2010 rohm co., ltd. all rights reserved. ordering part number b d 4 1 5 5 f v - e 2 part number part number package fv : ssop-b20 packaging and forming specification e2: embossed tape and reel (ssop-b20) (unit : mm) ssop-b20 0.1 11 10 20 1 0.1 0.1 6.4 0.3 4.4 0.2 6.5 0.2 0.15 0.1 0.22 0.1 0.65 1.15 0.1 0.3min. ? order quantity needs to be multiple of the minimum quantity. embossed carrier tape tape quantity direction of feed the direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand 2500pcs e2 () direction of feed reel 1pin
r1010 a www.rohm.com ? 2010 rohm co., ltd. all rights reserved. notice rohm customer support system http://www.rohm.com/contact/ thank you for your accessing to rohm product informations. more detail product informations and catalogs are available, please contact us. notes no copying or reproduction of this document, in part or in whole, is permitted without the consent of rohm co.,ltd. the content specied herein is subject to change for improvement without notice. the content specied herein is for the purpose of introducing rohm's products (hereinafter "products"). if you wish to use any such product, please be sure to refer to the specications, which can be obtained from rohm upon request. examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the products. the peripheral conditions must be taken into account when designing circuits for mass production. great care was taken in ensuring the accuracy of the information specied in this document. however, should you incur any damage arising from any inaccuracy or misprint of such information, rohm shall bear no responsibility for such damage. the technical information specied herein is intended only to show the typical functions of and examples of application circuits for the products. rohm does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by rohm and other parties. rohm shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. the products specied in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, ofce-automation equipment, commu- nication devices, electronic appliances and amusement devices). the products specied in this document are not designed to be radiation tolerant. while rohm always makes efforts to enhance the quality and reliability of its products, a product may fail or malfunction for a variety of reasons. please be sure to implement in your equipment using the products safety measures to guard against the possibility of physical injury, re or any other damage caused in the event of the failure of any product, such as derating, redunda ncy, re control and fail-safe designs. rohm shall bear no responsibility whatsoever for your use of any product outside of the prescribed scope or not in accordance with the instruction manual. the products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospac e machinery, nuclear-reactor controller, fuel- controller or other safety device). rohm shall bear no responsibility in any way for use of any of the products for the above special purposes. if a product is intended to be used for any such special purpose, please contact a rohm sales representative before purchasing. if you intend to export or ship overseas any product or technology specied herein that may be controlled under the foreign exchange and the foreign trade law, you will be required to obtain a license or permit under the law.

▲Up To Search▲

Price & Availability of BD4155FV

	To Download BD4155FV Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .